Drugasar Cello Balanced Flue Gas Fire
Maximum heat output 6.3Kw Up to 75% efficient Battery operated remote control as standard Realistic flame effect Glass fronted hole in the wall gas fire Metal interior lining Alu Metallic, Sand Metallic, Anthracite or Shadow Brown (Cello shown opposite with Alu Metallic trim finish Log fuel effect Balanced flue gas fire (BF) designed primarily for homes without a chimney or flue with an immediate external wall. However a UK Chimney conversion kit is available (please read the notes section at the bottom of this page for further details about the "Standard Balanced flue kit" & "Chimney Conversion Kit" available at additional cost with this fire) Natural gas only Depth of 347mm fully inset

Finishes

Dru Cello Alu Metallic Finish	Dru Cello Anthracite Finish	Dru Cello Sand Metallic Finish
Dru Cello Shadow Brown Finish

Hearths and Backs

Drugasar Metal Interior Lining Drugasar

Fuel Effects

Drugasar Logs

Gas Types

Drugasar Mains Natural Gas (NG)

Controls

Drugasar Remote Control With Temperature Display

Optional Extras

Please call 0845 301 5552 for a price

Specification

External Dimensions H 915mm W 797mm D N/Amm Inset Dimensions H 947/997mm W 685mm D 347mm OutPut Maximum heat output high 6.3Kw (NG)

Details Contemporary Hole in the wall Balanced Flue Gas Fire with optional Chimney conversion kit Flue No chimney required as this fire is a balanced flue gas fire which vents up vertically then horizontally directly through an external wall. Although there is a Chimney conversion kit available (see the notes section below for further details) Ventilation An air vent is not normally required

Notes
NOTE: Please ensure to have a survey carried out by a Corgi registered gas installer to check and certify the compatibility of your room and intended location with this fire before making any purchase to avoid disappointment Also ensure to study all the relevant information for installation of this appliance by reading the online installation & user instructions provided by Drugasar at www.drufire.co.uk before proceeding to purchase, as we cannot accept any liability in the event that this product proves to be unsuitable for your needs or circumstances. When installing this product as a balanced flue on an immediate external wall you will also need to to construct a false chimney breast to house the depth of the fire and line it with non combustable material. The standard balanced flue kit supplied with the fire consists of 1 1000mm length, 1 90 degree bend and 1 wall flue terminal kit. The 1000mm length comes off the top of the fire and raises up vertically before venting horizontally at 90 degrees through the thickness of a standard external wall. However there is a Chimney conversion kit available for standard 2 storey buildings of normal size & height to enable this fire to operate within an UK style Chimney breast, which consists of 1 short vertical flue / roof terminal, 1 flat roof tile aluminium plate, 10 metres of flexible 80mm flue pipe, 1 chimney closure plate, 1 flexible 80mm flue adaptor and 1 500mm concentric adjustable flue pipe 150 / 80 (NOTE: Additional flue pipe & accessories are available prices on request). This appliance also comes standard with a temperature display remote control which allows the flame height to vary between high and low from your armchair once the pilot has been ignited manually. Also be aware that due to the fire producing heat the interior of the fire may become marked over time through general wear and tear which is quite normal and to be expected. The inside of the glass may also require cleaning from time to time due to condensation that may form on the inside of the glass. Due to the number of size measurements and complexity of this fire it is strongly reccomended that you have the appliance on site / in your possession to take accurate measurements from before proceeding to construct any any false walls or chimney breast to avoid potential mistakes being made. For more detailed information about this product including down loadable technical user & installation instructions, simply click on the customer services heading at the top of this page, then click brochures and scroll down to Drugasar where you can link directly to their website or alternatively you can email a request for a brochure.